Hallo Zusammen.
Kennt jemand diesen Sitz und kann etwas dazu sagen?
Gruß Arndt
Um schreiben oder kommentieren zu können, benötigst du ein Benutzerkonto.
Du hast schon ein Benutzerkonto? Melde dich hier hier an.
Jetzt anmeldenHier kannst du ein neues Benutzerkonto erstellen.
Neues Benutzerkonto erstellenHallo Zusammen.
Kennt jemand diesen Sitz und kann etwas dazu sagen?
Gruß Arndt
sieht aus wie eine chinesische Grammer Kopie ... bei den Kosten rate ich Dir Dich nach gebrauchten ISRI oder Grammer umzuschauen ... die dann ggf. neu polstern oder zumindest beziehen und gut ist bei weniger Invest
Ach fällt mir gerade ein ... ggf. kann ich einen vermitteln ... bei Interesse PN ... ich frage gleich mal nach
Sieht mehr nach einem amerikanischen Produkt aus...
Brand New Prime 400L Seat
Truck, Bus, Van Seat
Helps Maximize Your Comfort And Allows For Healthy Driving Positions the Whole Time You Are On The Road
Functions and Features
Air Height Adjustment (6")
Fore & Aft Slide Adjustment (Total Travel 7.5')
Fore/Aft Isolator (Lock/Unlock Position)
High Back Profile Back Rest
Upholstery - Ultra Leather
Covering- 2 Tone Grey Leather (TPU)
Dual Adjustable Arm Rest
Fully Reclining Backrest (Almost Flat)
Lower and High Dual air lumbar & Bolster Support
Seat Cushion Extension (5 different Length Adjustment)
Seat Tilt Adjustment (5 Different Tilting Position)
Adjustable Shock Absorber :11 different setting Soft to Hard
12V Heating Seat (Bottom and Back)
*bolded section represents advantage over previous model
Dimensions
Bottom Cushion Width: 21"
Height from bottom to top of bottom cushion: 13.5-20.5"
Total Height with no air: 44"
Total Height with full air: 50"
Back Rest Width without armrests: 20.5"
Back Rest Width with both arm rests 26"
Arm Rest width: 2.5"
Prime seats come with a riser that can be easily removed to make a lower profile seat with a bolt pattern of 11" x 8.25". This lowers the seat 4.25" and makes the hip point 9" without air and 15" with full air. Or the standard bracket can be replaced with the Low-Profile Bracket to decrease the height by 2.25". Call for additional information.
Application Guide
Freightliner: Century, Classic, Cascadia, Classic XL, Columbia, Coronado, Coronado SD, FLD, FLD SD
International: 4000 Series, 5000 Series, 7000 Series, 8000 Series, 9000 Series, DurasStar, PayStar, ProStar, TerraStar, TransStar, WorkStar
Kenworth: C500, T470, T600, T660, T700, T800, T900, T2000, W900
Mack: CH, CX, Granite, GU, Pinnacle, Titan, TD, Vision
Peterbilt: 320, 325, 330, 337, 348, 365, 367, 379, 382, 384, 385, 386, 387, 388, 389, 587
Sterling: Acterra, AeroMax, A-Series, Louisville, L-Series
Volvo: VHD, VN, VNL, VNM, VT, WAH, WCA, WG, WIA
Western Star: 3800, 4800, 4900, 5900, 6900, LowMax, Stratosphere
A special adaptor is needed for the following models
International:ProStar, LoneStar, TranStar since2002, WorkStar since 2002, DuraStar since 2001, TerraStar, 8000 Series since 2002, 700 Series since 2002, and 4000 Series since 2001
Volvo: VHD Since 2000, VN Since 2000, VNL Since 2000, VNM Since 2000, VT Since 2000
DUE TO WEIGHT RESTRICTIONS, THIS ITEM CAN ONLY BE SHIPPED INSIDE THE LOWER 48 STATES TO A COMMERCIAL ADDRESS OR BE PICKED UP AT A LOCAL TERMINAL. Call or message for details
Hi Arndt!
Ob Chinaschrott oder Ami wäre mir in dem Fall egal. Das Problem, wo ich sehe, ist bei den Ersatzteilen.
Für Isri, Grammer, usw bekommst halt Dein Zeug, wenn was ist....., das hast bei den Chinesen gar nicht, und bei den Ami´s nur, wenn Du viel Glück hast.
Also, wenn Du eh schon in der Preisregion einkaufen willst, bekommst da auch etwas gut Gebrauchtes.....
Ok. Überzeugt
....ich spreche aus leidiger Erfahrung....
Ich hatte mal einen Chinesen-Radlader......
NIE wieder!!!!
Ich hatte mal ne chinesische Freundin. War auch nichts...
...wahre Freundschaft gibt´s eh nur unter Männern ....
So ist es...
Hab noch 2 Sitze da, kannste dir anschauen, nie verbaut keine Risse oder Flecke.
Äh - ich hätte auch noch nen Grammer hier rum stehen den ich vermutlich nicht einbaue .......
...solltest du aber - ist ein toller Sitz. Habe ich auch bei mir drin.
Da mein mechanischer ISRI völlig fertig ist, suche ich einen vernünftigen Sitz, genauer gesagt meine fehlenden Bandscheiben suchen einen. Mein Geldbeutel wehrt sich allerdings noch.
Die, welche hier einen angeboten haben, können ja ggf. mal einen Preis in den Raum werfen.
Danke.
Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!